Taika - Pearl Paint

Water-borne, tintable, acrylate paint for a pearlescent effect.
For interior painting on wooden, wood fibre board, particle board and metallic surfaces and plasterboard (gypsum board), concrete and similar surfaces.
Anbefalede anvendelser
For use on interior walls, furniture, etc. where a fancy effect is required. Can be used for first-time painting or patching up, and on substrates previously painted with alkyd or catalytic paint, or on lacquered surfaces. Good lighting accentuates the fancy effect.
Taika Pearl Paint, Gold and Silver

Malingen er velegnet til vægge Malingen er halvblank Malingen er vandbaseret Værktøj rulle Værktøj spray Værktøj pensel
Dækningen af ​​maling på ru overflader
Dækningen af ​​maling på glatte overflader
Base paints
HM og KM
Farve Område
Taika colour card
Glans grad
Byggemateriale emissionsklasse
6-8 m2/l.
Emballages størrelser
0,1; 0,225; 0,9 and 2,7 liters
Påførings metode
Brush, effect roller, spray. For application use a short-pile roller. Use brush or effect roller to create different surface patterns.
Conventional spray: fluid nozzle 1.8mm, thinning up to 40 % with water.
Thinner: if necessary thin with water

Tørretid ved 23°C og 50% relativ luftfugttighed
Touch-dry after one hour. Recoatable after 6-8 hours.
Resists over 5000 brushings (SFS 3755).
Varme bestandighed
+85°C, ISO 4211-3.
Tørstof volumen
Approx. 35%
1.1 kg/l (without tinting) (ISO 2811)
Protect from frost.

The surface to be treated must be dry, the temperature of the air at least +10ºC, and the relative humidity of the air below 80 %. A fairly low temperature (approx. +15º C) and a fairly high humidity (50-70 % RH) prevents the paint from drying too quickly and makes work easier.
Unpainted surfaces: Clean new surfaces carefully of dirt and dust, to ensure the best possible adhesion.
Wood surfaces: Treat knots with Oksalakka knotting lacquer. Prime with Helmi Primer/Feelings Furniture Primer or Otex primer. New clean wooden surfaces in good condition can also be treated directly with Taika Pearl Paint.
Metal surfaces: Metal surfaces should be primed with Rostex anti-corrosion primer.
Wall surfaces: If necessary, smooth the surface with a Presto filler and sand the dry surface. Remove sanding dust. Apply two coats of Tikkurila acrylate wall paint, such as Harmony/Feelings Interior Paint.
Previously painted surfaces: Wash down previously painted surfaces with Maalipesu cleaning agent and rinse carefully with water. Allow to dry.
Wood surfaces: Remove loose paint or lacquer with a scraper. Sand hard and glossy painted or lacquered surfaces matt. Remove sanding dust. Fill holes and cracks with Presto Rapid Filler and sand filled places. Prime unpainted surfaces.
Please note: use Otex primer on surfaces covered with nitrocellulose lacquer.
Wall surfaces: Sand hard and glossy surfaces matt. Remove sanding dust. Fill holes and cracks with Spakkeli or Presto Filler and sand the dry surfaces. Remove sanding dust. Prime unpainted surfaces.

Stir the paint carefully all the way to the bottom before use. Furniture, etc.: Apply two coats of Taika Pearl Paint by brushing, rolling or spraying. On large surfaces, it is worth first applying with a roller and then smoothing it with a brush. Use a high-quality synthetic-fibre brush. The pearlescent effect is beautifully accentuated in the brush strokes. Wall surfaces/effect painting: On wall surfaces, Taika Pearl Paint works best as a limited effect surface, whereby part of the wall paint used as a 'primer' is left visible. From the Taika colour card, you will find colours for wall paints that match Taika Pearl Paint. Apply Taika Pearl Paint with a roller in areas of about 1m² at a time, and, if desired, immediately create effects using different effect rollers, brushes or sponges. A trial painting on thick cardboard is recommended. We recommend that you protect the skirtings carefully with masking tape. Remove the masking tape immediately after painting. If you use a brush, work with small areas and finish immediately with a roller. In that way, border areas are not so easily visible. Apply two coats of Taika Pearl Paint, but in effect painting, only one. Painting large, smooth, even surfaces with Taika Pearl Paint requires skill and experience, but such methods as criss-cross brushing or rolling also work for beginners, even on larger wall surfaces. Taika Pearl Paint is also suitable for patterning with stencils and for line painting. Further ideas and more detailed instructions can be found in the Tikkurila Painting Guides.
Rengøring af værktøj
Remove excess paint from the tools. Wash the tools with soap and water. For cleaning slightly hardened paint, we recommend Tikkurila Pensselipesu (Tool Cleaner).
Not until 1 month after painting: Clean the surfaces with neutral (pH 6-8) dishwashing liquid and with soft brush, sponge or cloth. Clean the very dirty surfaces with lightly alkaline (pH 8-10) washing fluid with cloth, mop or sponge. Rinse the surface carefully.

After painting the surfaces must be handled carefully for a few weeks time, because the paint will achieve its final hardness and durability in normal conditions after 1 month. If the surface must be cleaned soon after painting, clean the surface lightly with soft brush, cloth or mop.
Follow the instructions of previously painted surfaces. If desired the effect surfaces can be recoated with Helmi Furniture Paint (furniture) or with water-borne wall paints (wall surfaces).
EU VOC 2004/42/EC-limit værdi
(cat A/l) 200g/l (2010)
Taika Pearl Paint VOC max. 200 g/l.

The product is not classified as dangerous. Handle with care. Avoid prolonged contact with skin and breathing of spray mist. A Material Safety Data Sheet is available at request.
Material Safety Data Sheet - TAIKA Pearl Paint

Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
VAK / ADR: not classified
sre091210 / mli080906 / hok120906 / tho140906 / 858 6085-6