Kiva Furniture Lacquer, semi-gloss
Waterborne low-odour non-yellowing acrylate lacquer for use on interior wood surfaces.
For use on interior wood surfaces. Kiva Interior Lacquer can also be used for the protective lacquering of stained surfaces. Not suitable for use on floors.
Tables, chairs, bookshelves, panelled walls and ceilings, doors, toys, etc. Kiva Furniture Lacquer can also be used for the protective lacquering of stained surfaces.
Tikkurila Interior Lacquer Colour Card.
8-14 m2/litre per coat. Actual spreading rates will depend upon
many factors including texture, porosity, moisture content of the substrate and
method of application.
0,225, 0,9, 2,7, 9 l
Brush, sponge or spray. Polyester or nylon paint brushes are best suited for
the application of Kiva Interior Lacquer.
Tørretid ved 23°C og 50% relativ luftfugttighed
Normally touch-dry in ½ hour and recoatable after 2-3 hours. The lacquered
surface will reach final hardness after approximately 2 weeks. Hard stress and
the placing of objects on the surface should be avoided during this time.
Good (DIN 53778)
Good (ISO 2812-1). Resists cleaning chemicals, weak solvents e.g. white spirit. Spillage of coffee, tea, etc. should be wiped off immediately.
Good oil and grease resistant.
Approx. 32 %
Approx. 1,0 kg/l, ISO 2811.
Protect from frost.
All surfaces to be painted must be dry, the temperature of the air and substrate at least +10OC, and the relative humidity of the air below 80%.
Surfaces must be clean, dry, and free from grease, dirt, oil, wax, all loose material and surface contamination. Wet new wooden surfaces with clean water so as to expose loose wood fibres, allow to dry and sand down. Completely remove existing coatings that are in poor condition. Use suitable Tikkurila products such as cleaning agents and suitable Tikkurila wood fillers for filling cracks, nail holes, blemishes, etc. Ensure that all glossy and filled surfaces are thoroughly flatted down.
Stir thoroughly before and during use. Apply two to three coats of Kiva Furniture Lacquer according to the condition of the surface and required depth of colour. Always work in the direction of the grain and avoid overlapping. The final colour will depend upon the timber species i.e. original colour and hardness. The chosen gloss level will normally be achieved after the application of two coats.
A trial painting on a separate piece of wood is recommended to check the right colour when using tinted product. The final colour of the treated surface depends on wood species, the hardness and the original colour of the wood, and the number of coats applied. Thin tinted lacquer for the first treatment with 20-30% water. Usually the desired result will be achieved with two coats. Treat surfaces always without a break and large panel surfaces a few panels at a time to achieve an uniform colour.
Rengøring af værktøj
Clean with water immediately after use. Tikkurila Pensselipesu (Tool Cleaner) is recommended to be used for cleaning hardened paint from tools.
Do not clean earlier than 1 month after treatment.
Clean the surface with a damp cloth, sponge or soft brush and with neutral (pH 6-8) detergent. The surface must not be left wet after cleaning. Very dirty surfaces can be cleaned with a slightly alkaline (pH 8-10) detergent using e.g. a cloth, mop or sponge. Rinse the surface carefully.
Maintain with Kiva Furniture Lacquer or a similar water-borne lacquer.
EU VOC 2004/42/EC-limit værdi
(cat A/e) 130g/l(2010)
SUNDHED OG SIKKERHED KLASSIFICERING
MILJØBESKYTTELSE OG BORTSKAFFELSE AF AFFALD
Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
mli231006 / lko071106 / tho261006 / 853-s,854-s,855-s