Tikkurila
PRODUCT DATA SHEET
29.02.2008
 

Jalo - Matt Lacquer

Beskrivelse
Alkyd lacquer.
Produktegenskaber
For varnishing interior wooden, wood fibre board and chipboard surfaces
Anbefalede anvendelser
Furniture and panel walls, ceilings, glass surfaces and doors. Jalo is not suitable for panel ceilings in premises with ceiling heating system.

TEKNISKE DATA
Malingen er velegnet til vægge Malingen er mat Malingen er fortynder-baseret Værktøj spray Værktøj pensel
Dækningen af ​​maling på ru overflader
12
m2/l
Dækningen af ​​maling på glatte overflader
14
m2/l
Glans grad
Mat
Dækning
12-14 m2/l.
Emballages størrelser
1/3 l, 1 l and 3 l.
Fortynder
Mineralsk terpentin 1050
Påførings metode
Brush or spray
Airless spray:
- nozzle 0.009" - 0.013" i.e. 0.230 - 0.330 mm
- thinning 0-5 vol-%

Tørretid ved 23°C og 50% relativ luftfugttighed
Touch dry after 4 hours. Sandable in 12 hours after priming, and after the second or third coat application in 24 hours.
Vaskbarhed
Good with all ordinary cleaning detergents.
Kemisk bestandighed
Resists White Spirit and Methylated Spirit, does not resist e.g. Thinner.
Slidstyrke
Good
Olie og fedt bestandighed
Resists lubricating oils and greases, vegetable and animal fats.
Tørstof volumen
41 %.
Densitet
0.9 kg/l, ISO 2811.
Opbevaring
Endures cold storage and transport. Poorly closed or short can does not endure long storage.
Produktkode
005_0443
MED-certifikat

PÅFØRING
Påførings-betingelser
The surface to be treated must be dry, the temperature of the air at least +5 ºC, and the relative humidity of the air below 80 %.
Forberedelse
New untreated surfaces:
Clean dirt and dust from untreated surfaces. Fill knot spots and unevenness with Spakkeli wood putty pine. Sand the filled spots and remove sanding dust.

Previously treated surfaces:
Wash down previously treated surfaces with Cleaning Agent (Maalipesu) and rinse carefully with water. Remove loose or flaking paint with a scraper. Sand the whole surface and remove sanding dust.
Lakering
Stir JALO thoroughly up to the bottom before use and also from time to time during the use.
Thin Jalo for priming with 10 % White Spirit 1050. Sand the dried surface lightly after the priming and remove sanding dust. Finish with unthinned lacquer.
A beautiful glazing colour is achieved by treating the bare wooden surface with Parquet-Ace Stain, Unica Super or Panel-Ace before applying Jalo. Do not thin tinted Parquet-Ace Stain. To attain smooth colour, thin Unica Super and Panel-Ace with 20%. Thin Unica Super with White Spirit 1050 and Panel-Ace with Water.

Note! For porous wooden surfaces (especially for stained end surfaces) it is recommended to apply a test coat. If the lacquer surface turns to grey, prime the wooden surface first with a glossy lacquer e.g. Unica Super. Finish then with Jalo matt lacquer.
Rengøring af værktøj
Clean tools with White Spirit 1050.
Vedligeholdelsesvejledning
Jalo Matt Lacquer reaches its final durability in approx. 1 month. Avoid cleansing during that time.
Clean surface with a neutral (pH 6-8) dishwashing agent using a soft cleaning towel. Rinse and dry immediately after treatment.

After treatment, treat surface with care for a few weeks. Surface reaches its final hardness and durability in approx. 1 month under normal circumstances. If needed, clean surface with a soft brush, a damp rag or mop.
EU VOC 2004/42/EC-limit værdi
(cat A/e) 500g/l(2007)/ 400g/l(2010)
Jalo contains VOC max. 500g/l.

SUNDHED OG SIKKERHED KLASSIFICERING
Contains: Naphtha, hydrotreated heavy. FLAMMABLE. Do not breathe vapour/spray. Use only in well ventilated areas. If swallowed, seek medical advice immediately and show this container or label. Keep out of reach of children. Contains methylethylketoxime and cobalt octoate. May produce an allergic reaction. A Material Safety Data Sheet is available on request.
Material Safety Data Sheet - Jalo

MILJØBESKYTTELSE OG BORTSKAFFELSE AF AFFALD
Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations. Risk of self-ignition! Cleaning cloths, sanding dust and overspray containing the product can create fire by self-ignition. Waste like this should be collected and stored e.g. in water before disposal or be dried preferably outdoors.
TRANSPORT
ADR: 3 III, Drums/vessels < 450 litres: not subject to ADR because of high viscosity
ssa290208 / ars260308 / tpi250308 / mli070906 / mit121006 / 005 0443